Models covered
Parts
Parts and accessories for Melitta Barista TS F730-101
Compare the documented references, including 6764995. Open the part details to check the complete model code, then view the retailer’s offer.
Melitta Avanza/Barista milk tube
Melitta official avanza/barista milk tube, reference 6764995. Compatibility is published only for the exact appliance codes explicitly listed by the manufacturer source.
Start with the full Melitta Barista TS Smart model code and the precise “milk is not drawn from the container” display pattern; a similar warning may require a different check. Limit this Melitta Barista TS Smart check to accessible containers, the removable brew path and the milk or drainage parts named in the manual. What this exact symptom means: the steam tube at the milk-container lid or the milk-system tube at either end may not be fully connected.
What to distinguish first: Confirm that the displayed or observed condition exactly matches “milk is not drawn from the container” before changing anything. 1. Confirm the model and signal — Confirm that the displayed or observed condition exactly matches “milk is not drawn from the container” before changing anything. 2. Prepare the appliance safely — Let Melitta Barista TS Smart finish its normal shutdown, unplug it, allow hot surfaces to cool and empty the drip tray before removing an accessible part.
3. Carry out the official user check — With all milk parts cool, press the steam tube into the lid and reseat both ends of the milk tube at the outlet and container, then rinse once. 4. Interpret one controlled retest — Refit Melitta Barista TS Smart exactly as documented and perform one short rinse or drink test. The cited Melitta Barista TS Smart manufacturer documentation links “milk is not drawn from the container” to the user-level procedure described here.
Before checking Melitta Barista TS F730-101
- Protect Melitta Barista TS Smart's electrical openings and grinder from water; a brew unit, valve or hot steam fitting that resists must not be forced.
What this symptom can mean on Melitta Barista TS F730-101
4 checks for Melitta Barista TS F730-101, starting with Confirm the model and signal
- Confirm the model and signal
Confirm that the displayed or observed condition exactly matches “milk is not drawn from the container” before changing anything.
- Prepare the appliance safely
Let Melitta Barista TS Smart finish its normal shutdown, unplug it, allow hot surfaces to cool and empty the drip tray before removing an accessible part.
- Carry out the official user check
With all milk parts cool, press the steam tube into the lid and reseat both ends of the milk tube at the outlet and container, then rinse once.
- Interpret one controlled retest
Refit Melitta Barista TS Smart exactly as documented and perform one short rinse or drink test. If “milk is not drawn from the container” returns, stop resetting and arrange service.
When to stop checking Melitta Barista TS F730-101
- End the Melitta Barista TS Smart check if “milk is not drawn from the container” persists, the grinder is obstructed, hot water leaks or power trips; those signs require service.
Next step
What the Melitta Barista TS F730-101 checks lead to
The 4-check path for “Melitta Barista TS Smart: milk is not drawn from the container” starts with “Confirm the model and signal” and separates a resolved condition, an identified part and a case requiring service.
No purchase after a successful check
Follow the Melitta Barista TS F730-101 controls in order. If “Confirm the model and signal” and the remaining checks restore normal operation with no warning, stop without replacing anything.
Escalate only on the documented warning signs
For “Melitta Barista TS Smart: milk is not drawn from the container”, use the stop conditions above rather than the symptom by itself. Professional confirmation should precede any decision to replace Melitta Barista TS F730-101.
Sources used
- Melitta · source in French — The cited Melitta Barista TS Smart manufacturer documentation links “milk is not drawn from the container” to the user-level procedure described here.
Last checked: 30 August 2026